Single coated linear joint seals
Size: 100 x 200 x 1200mm
Please Note: this item may take 7-10 working days for delivery.
Description
As part of the comprehensive FIREPRO range of fire protection products, ROCKWOOL FIREPRO SoftSeal System incorporates a product specifically designed to form a linear joint seal within buildings, where the design needs to accommodate movement in the joint.
It may be installed horizontally or vertically and is suitable for linear joint widths up to 300mm*. FIREPRO SoftSeal Linear Joint Seal can also be used as a ‘head-of-wall’ barrier to extend the fire resistance and acoustic performances of masonry walls that finish at suspended ceiling height, up to the concrete soffit above. FIREPRO SoftSeal Linear Joint Seal can be used in conjunction with ROCKWOOL Ablative Coated Batt for head-of-wall applications.
A FIREPRO SoftSeal Linear Joint seal comprises a low-density stone wool FIREPRO SoftSeal batt, pre-coated with FIREPRO SoftSeal Flexible Coating. Depending on the application, FIREPRO SoftSeal Linear Joint Seal can be supplied on either one or both sides. (Single Sided for Horizontal Applications. Double sided for Vertical Applications).
The FIREPRO SoftSeal Flexible Coating is also available in 5L, 10L and 20L tubs to enable site repairs to FIREPRO SoftSeal Coated Strips and FIREPRO SoftSeal Linear Joint Seals, that may have been damaged during installation.
The FIREPRO SoftSeal Linear Joint Seal is supplied in strips 1200mm x 200mm x 100mm
Performance
Fire performance
ROCKWOOL FIREPRO SoftSeal Linear Joint Seal has been tested to the dedicated fire resistance standard for linear joint seals BS EN1366-4 and shown to provide up to 4 hours fire performance (E240 & EI80).
Movement
As part of the testing to BS EN 1366-4, FIREPRO SoftSeal was assessed for its movement capabilities, prior to conducting the fire test. The product was tested to accommodate movement (expansion and contraction) of +/-25%.
Acoustics
Tested to EN 10140 based on two thicknesses with the following results:
- Rw 30 dB: When installed with 100mm thick SoftSeal Batt
- Rw 39 dB: When installed with 200mm thick SoftSeal Batt
- Dn,e,w 40 dB: When installed with 100mm thick SoftSeal Batt
- Dn,e,w 49 dB: When installed with 200mm thick SoftSeal Batt
Water permeability
Tested to EN 1027 - No leakage observed up to 300Pa.
Air permeability
- Tested to EN 1026 up to 600Pa.
- Leakage at 50Pa - 0.1/1.4 m³/m²/h.
Technical information
Standards & Approvals
FIREPRO SoftSeal has been tested and assessed to BS EN1366-4: 2006 + A1: 2010 and classified to EN 13501-2.
FIREPRO SoftSeal Linear Joint Seal system has been CE marked against ETAG026-3
Property Description
Length: 1200mm
Width: 200mm
Thickness: 100mm
Fire Resistance: Up to 4 hours
Coating: 1 side
Density: 80Kg/m³
Movement: +/- 25%
Product Data Sheet
Data Sheet Links
Installation Sheet
Safety Data Sheet - Coating
Safety Data Sheet - Insulation
Technical Data Sheet
The above information is based on current test data, health and safety information and application instructions supplied by our suppliers and manufacturers of the products. It is supplied for guidance and to the best of our knowledge is true and accurate. Customers should satisfy themselves to the suitability of the products in its intended use and no guarantee is given or implied as the conditions of actual use are beyond our control. If in doubt the customer should consult the designer of the project or the local building control.
Fire Stopping Shop, disclaim any liability for loss, damage or other expense which may arise from the use of this information, data or products refereed to and reserve the right to amend or change any details without notice. This statement does not affect your statuary rights.